Question 1

For output to equal projected demand, what is the minimum number of workstations needed?

Accepted Answer

A)  2
B)  2.8
C)  3
D)  4
E)  5F) A) and E)
G) A) and D)

Question 2

If departments A through D were to be located in areas 1 through 4, respectively, what would be the total distance loads would be moved each month?

Accepted Answer

The answer of If departments A through D were to...

Question 3

If transportation costs are $.25 per load per foot moved, what are total monthly costs for an optimum layout?

Accepted Answer

The answer of If transportation costs are $.25 per load...

Question 4

The maximum allowable cycle time is computed as:

Accepted Answer

A)  daily operating time divided by the desired output
B)  desired output divided by the daily operating time
C)  daily operating time divided by the product of the desired output and the sum of job times
D)  the product of desired output and the sum of job times divided by daily operating time
E)  1.00 minus station timeF) B) and C)
G) A) and E)

Question 5

Layout design has many objectives, one of which is ______.

Accepted Answer

A)  reduce bottlenecks
B)  move materials and workers simultaneously
C)  use workers and space efficiently
D)  hold material handling costs to 27% or less
E)  install computer terminals every 500 feetF) C) and D)
G) All of the above

Question 6

Given the information below, assign the departments A through I to locations in a 3 x 3 grid, with department E fixed in the lower right-hand corner.

Accepted Answer

The answer of Given the information below, assign the departments...

Question 7

Heuristic approaches to line balancing are the only approach that will guarantee an optimal solution.

Accepted Answer

A) True 
 B)False

Question 8

What is the maximum possible cycle time?

Accepted Answer

The answer of What is the maximum possible cycle time?...

Question 9

Which of the following is not an information requirement for the design of a process layout?

Accepted Answer

A)  a list of departments or work centers
B)  a projection of work flows between the work centers
C)  the distance between locations
D)  the cost per unit of distance to move loads
E)  a list of product cycle times for every product manufacturedF) A) and E)
G) B) and E)

Question 10

What is the total flow (loads per week)  between department Y and department Z?

Accepted Answer

A)  140
B)  160
C)  200
D)  250
E)  300F) B) and C)
G) A) and E)

Question 11

If the company desires that output rate equal demand, what would be the efficiency of this line with the minimum number of workstations?

Accepted Answer

A)  100%
B)  92.5%
C)  75%
D)  87.5%
E)  90%F) A) and E)
G) None of the above

Question 12

Process layouts tend to have low in-process inventories.

Accepted Answer

A) True 
 B)False

Question 13

Which one of these is a tool used to tell a machine the details of the operations to be performed?

Accepted Answer

A)  CNC
B)  CIM
C)  CAD
D)  CAM
E)  automationF) B) and E)
G) C) and D)

Question 14

There are three basic process types - Input, Processing and Output.

Accepted Answer

A) True 
 B)False

Question 15

Numerically controlled (N/C) machine and some robots are applications of programmable automation.

Accepted Answer

A) True 
 B)False

Question 16

Which of the following is a primary concern for process selection?

Accepted Answer

A)  variety in products/services
B)  flexibility of equipment
C)  volume of output
D)  all of the above
E)  none of the aboveF) None of the above
G) A) and D)

Question 17

Which type of processing system tends to produce the most product variety?

Accepted Answer

A)  Assembly
B)  Job-Shop
C)  Batch
D)  Continuous
E)  ProjectF) B) and D)
G) All of the above

Question 18

An operations strategy for process selection should recognize that:

Accepted Answer

A)  process selection seldom requires technical expertise
B)  engineering "white elephants" are uncommon
C)  there is little need to manage technology
D)  flexibility is not always the best choice
E)  most technical skills can be contracted out to consultantsF) B) and C)
G) C) and D)

Question 19

Heuristic rules are usually applied when:

Accepted Answer

A)   an optimum is necessary
B)   a computer program isn't available
C)   a problem has a small number of alternatives
D)   a problem has a large number of alternatives
E)   other approaches have failedF) D) and E)
G) All of the above

Question 20

Which closeness rating reflects the highest importance for two departments being close to each other?

Accepted Answer

A)  A
B)  E
C)  I
D)  U
E)  XF) B) and D)
G) C) and E)

Exam 6: Process Selection and Facility Layout

Heuristic rules are usually applied when:

Correct AnswerverifiedShow Answer

Given the information below, assign the departments A through I to locations in a 3 x 3 grid, with department E fixed in the lower right-hand corner.

Correct AnswerverifiedShow Answer

The maximum allowable cycle time is computed as:

Correct AnswerverifiedShow Answer

Process layouts tend to have low in-process inventories.

Correct AnswerverifiedShow Answer

Which of the following is not an information requirement for the design of a process layout?

Correct AnswerverifiedShow Answer

There are three basic process types - Input, Processing and Output.

Correct AnswerverifiedShow Answer

If the company desires that output rate equal demand, what would be the efficiency of this line with the minimum number of workstations?

Correct AnswerverifiedShow Answer

If departments A through D were to be located in areas 1 through 4, respectively, what would be the total distance loads would be moved each month?

Correct AnswerverifiedShow Answer

Layout design has many objectives, one of which is ______.

Correct AnswerverifiedShow Answer

Which closeness rating reflects the highest importance for two departments being close to each other?

Correct AnswerverifiedShow Answer

Which of the following is a primary concern for process selection?

Correct AnswerverifiedShow Answer

What is the maximum possible cycle time?

Correct AnswerverifiedShow Answer

Which type of processing system tends to produce the most product variety?

Correct AnswerverifiedShow Answer

If transportation costs are $.25 per load per foot moved, what are total monthly costs for an optimum layout?

Correct AnswerverifiedShow Answer

Which one of these is a tool used to tell a machine the details of the operations to be performed?

Correct AnswerverifiedShow Answer

Numerically controlled (N/C) machine and some robots are applications of programmable automation.

Correct AnswerverifiedShow Answer

Heuristic approaches to line balancing are the only approach that will guarantee an optimal solution.

Correct AnswerverifiedShow Answer

For output to equal projected demand, what is the minimum number of workstations needed?

Correct AnswerverifiedShow Answer

An operations strategy for process selection should recognize that:

Correct AnswerverifiedShow Answer

What is the total flow (loads per week) between department Y and department Z?

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified